Ricoma MT-1502 Common Errors & Solutions With Simple Maintenance

Embroidery digitizing services

We’ll talk about Embroidery digitizing services and Ricoma MT-1502 common errors and easy maintenance tips in this article.

Ricoma Mt 1502 Normal Mistakes and Arrangements:

On the Ricoma machine, you will learn how to easily fix common errors. Let’s get going:

1. The Ricoma Embroidery Machine’s Stitches Looping and Troubleshooting:

Circling of lines happens on account of erroneous stringing. Please check the bobbin thread for proper threading. Check the thread tension to see if the machine is properly threaded. Additionally, make sure to examine the needle. Looping and other issues with embroidery would be caused by an old or loose needle.

2. The same needles for every project:

Ballpoint needles could be utilized for a wide range of undertakings. However, we recommend using needles with a sharp point on satin, leather, or any other fine material. We suggest using an 80/12 needle for bulky fabric. We recommend using a 90/14 needle for metallic threads because its larger eye reduces friction during thread passage for Embroidery digitizing service.

3. Getting A X Or Y Cutoff Mistake And Investigating In The Ricoma Weaving Machine:

You are getting this mistake on the grounds that your logo may be extremely tremendous for the band, or you are attempting to fasten out the preset circle edge. You can use a big hoop or move the logo around so that it stays within the hoop’s boundaries.

4. Causes of thread breaks and how to fix them on the Ricoma embroidery machine:

Thread breaks are typically brought on by:

If you use the needle for a long time or on thick fabrics, it might be worn out.
It’s possible that your machine isn’t threaded properly. Make sure that each thread is positioned correctly by checking the thread passage.
Your thread may be too old or damaged, and prolonged exposure to light, heat, or air may weaken it. This can be avoided by storing thread in a cool, dark location.
Hooping probably won’t be adequately tight
The strain may be extremely close or exceptionally free

5. Using the Ricoma Embroidery Machine to Troubleshoot and Get Pinch on the Fabric:

This is as a result of a hooping mistake. You must ensure that the material is not creased and that the hooping is tight in order to achieve the desired tension. Make sure not to stretch the fabric because doing so could ruin the design. You could require a firm stabilizer.

6. Changing the Needle’s Size:

To control the bending of the needle, you must alter its size. The desired stitch size determines the needle size. Usually, larger needles are needed for bulky materials and smaller ones for light ones.

7. Replace needles frequently:

The three strikes rule is a basic rule that many experienced embroiderers use to determine when to change needles. When there are three thread breaks on a needle in a row, you must change it. If a needle breaks or is skipping stitches, you should change it.

8. Causes of Needle Breaking:

The design may have a lot of stitches for the area; you may have hit a hoop; the hooping may not have been smooth or tight; the material is too thick for the type of needle. Change Your Ricoma Embroidery Machine’s Thread:

To begin, remove the thread from the previous spool and insert a new one in its place. Then, tie a knot with the new thread’s loose end and the old thread’s loose end. In the end, take the thread from the presser foot and pull the new thread through the thread passage until it doesn’t get to the needle.

10. The Ricoma Embroidery Machine’s Troubleshooting and Needles Breaking on Hats:

There could be wear on the needle. The center of structured hats is made of thick cardboard or plastic, which could break the needle. Make sure the bill of the cap is as flat as possible when sewing it. Focusing on the digitized logo is likewise very huge. You must be aware of the logos that can be used on various materials. It’s possible that the way the DST was made shouldn’t be used on hats. Additionally, the hooping may not be accurate.

Simple Procedures for Ricoma Mt 1502 Repair:

Ricoma mt 1502 upkeep is a breeze. Lubricating the rotary hook is the most important piece of maintenance that needs to be done. We recommend turning off your machine before oiling or cleaning it. Remove the bobbin case from the rotary hook to begin cleaning and maintaining it.

Using a lint brush or dusting spray, clean any thread lint in the area.

Next, add:

to the rotary hook, three or four drops of machine oil.

You can now close the bobbin housing unit and return the bobbin case to the rotary hook.

If you intend to operate a machine for eight hours per day, repeat this procedure twice a day to ensure that it operates effectively.

Remove the needle plate once or twice per week and use a soft brush to clean the area around the trimmer knives.

Pass a piece of paper or a business card through the bobbin case slit once a week to remove any lint.

Place a drop of oil directly on the needle bar each week through the needle case’s slots; alternate weekly.

For a week:

lubricate the upper needle bar section and the lower needle bar section the following week.

Oil the needle plate’s opening once a week. To view the opening on the right side of the machine head for this section, we recommend turning the machine on and setting it to needle one.

Each week, add three drops of oil to that section.

Then, add three drops of oil to the machine head’s metal rail.

Move your machine head to needle 15 now, and add two drops of oil to the rail on the other side.

Apply white lithium grease to the black metal bar in the machine head once every three to five months. Also, grease the wheels on the back of your machine head with this grease.

Apply white lithium grease to the color change camera at least once every three to five months.

By loosening the screw that is attached, you would first need to take off the metal plate that is located above the color change cam. The color change cam should then be greased.

Before proceeding, place the cover back over the color change cam and tighten the screw.

Always keep in mind not to overuse oil. Before returning to production, stitch a test swatch to ensure that additional oil does not stain clothing.

Moving on:

We hope that you will find this article useful. Because digitizing is a complicated process, you would need to hire a professional like ZDigitizing if you want to digitize embroidery designs.

Zdigitizing:

Is a Embroidery digitizing services organization that gives total digitizing and vector workmanship benefits all around the world to organizations, enterprises, and companies. Zdigitizing offers services for custom digitizing embroidery and vector art that are high-quality, long-lasting, and affordable. Over the past two decades, we have been providing top-notch digitizing embroidery services.

Therefore, ZD will be your best option if you require a vector art or digitizing service for your embroidery machine with a lightning-fast turnaround and excellent quality. In less than five minutes, you can get a free quote by clicking the link below. All of our services are discounted by 50% when a potential customer places their first order with us.

I hope it will be of use to you both!

You can ask any questions you have about this article in the comment section. Don’t forget to share it with anyone you think might find it useful.

Lastly, thank you for reading!

Recommended Articles

Leave a Reply

Your email address will not be published. Required fields are marked *